Showmessage [ID] Console Command Help | Skyrim Console Commands

Command	Showmessage [ID]
Description	Shows a message in the center of the screen with the given ID.
Command Category	Other

General	Console commands are not case sensitive, so a lowercase a is the same as an uppercase A. Variables are inside brackets, [ ]. These are meant to be replaced with the quantity or ID you want.
How to Open the Skyrim Command Console	To open the console by press the ~ key, which is to the right of the 1 key and below the Esc key. Type in the command and then press the Enter key.

Command: Csb
Command Category: Other
Description: Clear Screen Blood. Removes any blood effects from the screen.

Csb

Command: Sqt
Command Category: Other
Description: Show Quest Targets. Gives a list of all targets for ongoing quests.

Sqt

Command: Refini
Command Category: Other
Description: Refreshes .ini settings (does not reset them).

Refini

Command: Sqo
Command Category: Other
Description: Show Quest Objectives. Gives a list of all objectives for ongoing quests.

Sqo

Command: Addtofaction [Factionid] [Number]
Command Category: Other
Description: Alternate version of AddFac, adds the selected NPC to a faction. May cause undesired and buggy AI behavior, 1–4 affects faction rank

Addtofaction [Factionid] [Number]

Command: Resetinterior [Locationid]
Command Category: Other
Description: Resets the given cell, reverting it to its original settings.

Resetinterior [Locationid]

Command: Load [Save Name]
Command Category: Other
Description: Loads the specified save. Requires quotation marks around the name if includes spaces.

Load [Save Name]

Command: Save [Save Name]
Command Category: Other
Description: Saves the game over an existing save with the specified name. Requires quotation marks around the name if includes spaces.

Save [Save Name]

Command: Prid [Refid]
Command Category: Other
Description: Sets the NPC as reference, allowing other commands to be used, good for targeting NPCs that cannot be reached/seleceted on screen or fixing quest glitches about NPCs not appearing.

Prid [Refid]

Command: Playercreatepotion [ID] [ID] [ID]
Command Category: Other
Description: Allows for potions to be created through the console. refers to the potion effect rather than the ingredient's ID. The second and third codes are optional.

Playercreatepotion [ID] [ID] [ID]

Command: Set Playerfollowercount To [Number]
Command Category: Other
Description: 0 Clears followers and allows one to recruit again.

Set Playerfollowercount To [Number]

Command: Stp [Number] [Number] [Number] [Number]
Command Category: Other
Description: Set Tint Parameters. Ranges from 0–1, with stp 0 0 0 0 creating the most vibrant display and stp 1 1 1 1 creating the most black and white display.

Stp [Number] [Number] [Number] [Number]

Command: Help
Command Category: Other
Description: List all console commands.

Help

Command: Modpcmiscstat [Miscstat] [Number]
Command Category: Other
Description: Modifies the specified miscellaneous stat of the player.

Modpcmiscstat [Miscstat] [Number]

Command: Getpcmiscstat [Miscstat]
Command Category: Other
Description: Returns the specified miscellaneous stat of the Dragonborn.

Getpcmiscstat [Miscstat]

Command: Removefac [Factionid]
Command Category: Other
Description: Removes the selected NPC from a faction. Usually used for unaligning hostile NPC from hostile factions. This may cause undesired and buggy AI behavior.

Removefac [Factionid]

Command: Set Playeranimalcount To [Number]
Command Category: Other
Description: 0 Clears non-humanoid followers and allows one to recruit again.

Set Playeranimalcount To [Number]

Command: Set Timescale To [Number]
Command Category: Other
Description: Set the rate at which time passes (20 is the default, 1 is realtime)

Set Timescale To [Number]

Command: Qqq
Command Category: Other
Description: Quits the game without going through the menus. (May cause crash.)

Qqq

Command: Getglobalvalue [Value]
Command Category: Other
Description: Returns information about the given value in the game's settings.

Getglobalvalue [Value]

Command: Saveini
Command Category: Other
Description: Saves all current game settings to the game's .ini files.

Saveini

Command: Pcb
Command Category: Other
Description: Purge Cell Buffer. Purges interior cells the Dragonborn has recently exited, potentially allowing for a higher framerate at the cost of longer loading screens.

Pcb

Command: Set [Variable] To [Number]
Command Category: Other
Description: Sets the specified variable.

Set [Variable] To [Number]

Command: Sw [Weather ID]
Command Category: Other
Description: Set Weather. Changes the current weather to the one entered. It may vanish quickly depending on the area the Dragonborn is in, due to the area's climate being forced.

Sw [Weather ID]

Command: Showglobalvars
Command Category: Other
Description: Shows all game variables.

Showglobalvars

Command: Help ["Object Name"] [Number]
Command Category: Other
Description: Show all console commands with descriptions. Add descriptors to search for IDs. ex: help "elven armor" 0 will show ids of all items that include "elven armor" in the name. Quotation mark is a must for items with more than one word ex: "elven armor," sets the limits for the search function, 0 = no limits; 4 = Exact.

Help ["Object Name"] [Number]

Command: Sgtm [Number]
Command Category: Other
Description: Set Gametime Multiplier. This changes the game speed (e.g. movement, dialogue, etc.), with a higher number leading to a faster speed and a lower number leading to a lower speed.

Sgtm [Number]

Command: Killall
Command Category: Other
Description: Kill a group of enemies.

Killall

Command: Addfac [Factionid] [Number]
Command Category: Other
Description: Adds the selected NPC to a faction. May cause undesired and buggy AI behavior, 1–4 affects faction rank

Addfac [Factionid] [Number]

Command: Getincellparam [Locationid] [Formid]
Command Category: Other
Description: Returns whether or not the specified object is in the specified cell. Ranges from 0.00–1.00, with 0.00 being not present and 1.00 being present.

Getincellparam [Locationid] [Formid]

Showmessage [ID]

More Commands